Jordan 191 Build

[Malc1]

2484AE0E-749C-466D-9514-EF13BAC7413C.jpeg (155.58 KiB) Viewed 3887 times

First one of these Open Wheel racers to have a go with for many years.
Tamiya Jordan 191 with photo etch upgrade set along with aftermarket decals.
Kit decals have basically had it due to age of the kit.
I’ll be using Zero paints of the correct colours .

Start of the body panel clean up and test fit ready for paint.

[Twokidsnosleep]

That’s a bit of all right!!!


Seven up has no cool images wait a tic......

[Malc1]

Due to the original kit decals being unusable and the painting of the second colour being required instead I decided to proceed for starters with just the main body panels to see how well it went.
Painted with Zero paints grey primer and Jordan green.

IMG_3547.jpg (148.79 KiB) Viewed 3799 times

I then traced off the decal sheet and made some templates in Tamiya masking tape.These I used to get the masking off positions hopefully somewhere near.
The aftermarket decal sheet has 0.5mm pinstriping which needs to go over the line between the green and blue.If the masking was off then it would not work out.

IMG_3534.jpg (79.4 KiB) Viewed 3799 times

IMG_3548.jpg (115.65 KiB) Viewed 3799 times

[Malc1]

Seems to be somewhere near so far.
A couple more decals on the tub and I'll clearcoat both to see what it looks like.

IMG_3558.jpg (100.97 KiB) Viewed 3796 times

IMG_3562.jpg (56.72 KiB) Viewed 3796 times

IMG_3568.jpg (119.96 KiB) Viewed 3796 times

[barryf1fan]

Love it, and the fact that you have the talent to still build it without the decals. I would have to chuck it out. That's a great looking car. Sub'd

[theoneaeon]

Looks good.

[Malc1]

Body work continuation

IMG_3582.jpg (255.94 KiB) Viewed 3730 times

[Malc1]

IMG_3624.jpg (158.16 KiB) Viewed 3726 times

[Malc1]

Now also started the prepping and painting of suspension and engine parts.

Cam shaft covers were done by first painting with Chrome acrylic and then over the top with black enamel and then removing the top coat with enamel thinners.

[Malc1]

On with the Bare Metal Foil..

IMG_3628.jpg (64.91 KiB) Viewed 3690 times

IMG_3630.jpg (62.14 KiB) Viewed 3690 times

[jmurphy18]

Very nicely done

[DRUMS01]

Your work looks great so far...

The shape of this F1 car was always one of the most beautiful (IMHO), regardless of its success.

Wonderful detail work on this classic.

Ben

[Malc1]

More painting finished tonight and another look at the photo edge grade up parts.
Just a few selected parts will be used I think and the rest will be standard kit.

IMG_3633.jpg (128.09 KiB) Viewed 3653 times

IMG_3634.jpg (360.02 KiB) Viewed 3653 times

IMG_3631.jpg (78.75 KiB) Viewed 3653 times

[Kevthemodeller]

How did I miss this lovely work mate

[Malc1]

Nice to actually get on with putting the Jordan together after weeks of preparing parts.
All straight forward so far and on to the nose cone assembly next.
Parts have been painted with a mixture of Zero and Tamiya LP.

IMG_3659.jpg (76.23 KiB) Viewed 3603 times

IMG_3658.jpg (108.22 KiB) Viewed 3603 times

IMG_3656.jpg (118.1 KiB) Viewed 3603 times

[Kevthemodeller]

Very nice

[Malc1]

Nose cone,top panel and side pods plus radiators fitted.

IMG_3664.jpg (141.54 KiB) Viewed 3564 times

IMG_3663.jpg (173.91 KiB) Viewed 3564 times

[barryf1fan]

Looking champ!! Can't wait for the final reveal.

[Kevthemodeller]

The paint finish looks superb mate

[Malc1]

The build continues with the lower side panels and engine assembly going in.

IMG_3667.jpg (102.14 KiB) Viewed 3499 times

IMG_3669.jpg (134.07 KiB) Viewed 3499 times

IMG_3692.jpg (361.96 KiB) Viewed 3499 times

[DRUMS01]

Simply wonderful.. not over done, and very, very clean build.

This is going to be a stunner.

Ben

[Malc1]

Kit is now more or less complete except for the GoodYear tyre decals and final assembly.

It turns out that the kit supplied decals are as shot as the main decal set and there is no way I can use them.
I'm just trying to source a set at the moment so hopefully I can get hold of some soon to fully complete the build.



Panel fixings added

IMG_3708.jpg (55.3 KiB) Viewed 3571 times

IMG_3700.jpg (148.03 KiB) Viewed 3571 times

IMG_3706.jpg (393.51 KiB) Viewed 3571 times

[DRUMS01]

You can get any style of tire Indy or F1 markings at:

[media]http://www.Indycals.net/[/media]

Great product too....

Ben

[Malc1]

Thanks for the link.

No 1/20 scale though,would have to see if I could get away with 1/18 or 1/25

Also shipping time from the USA to the UK may mean that the model is not done by the closing date.

[Kevthemodeller]

Very nice, all coming along very nicely

[Malc1]

Now calling this done

IMG_3720.jpg (466.88 KiB) Viewed 3482 times

IMG_3738.jpg (415.92 KiB) Viewed 3482 times

IMG_3730.jpg (469.01 KiB) Viewed 3482 times

[Kevthemodeller]

Oh yes superb build mate

[digger303]

Don't know how you could improve on that.....

[Modelfreek]

Just lovely to look at. Very nice clean paintwork. Well done!

[theoneaeon]

really nice looking build. Love it!!

[DRUMS01]

That turned out super sweet. For an out of the box build, that is top notch!

Where did you end up getting the tire decals?

Ben

[Malc1]

Managed to get a set made by Tabu Designs.
These were actually easier to apply than the Tamiya ones.
Being regular decals it was much easier to get them in the right position on the tyre.

I had Richy on the forum also send me out a couple of spare sets of Tamiya ones that he had but ended up going down the first route.
Tyre stencils were considered but decided against in the end.